金川集团化工厂铜冶炼烟气制酸中温位余热回收

阐述金川集团化工厂530 kt/a铜冶炼烟气制酸系统扩能改造和余热回收前存在的问题,在遵循尽可能保留现有工艺管线和保证余热高效回收的原则上对转化工艺进行改造完善,将转化流程由原设计的“3+1/Ⅳ.Ⅰ-Ⅲ.Ⅱ”四段转化改为“3+2/Ⅴ.Ⅰ-Ⅲ.Ⅱ.Ⅳ”五段转化工艺流程,研发适合冶炼烟气制酸系统的分离型热管余热回收工艺技术.生产实践证明,该工艺在确保转化热平衡的基础上提升转化率,优化系统工艺技术指标,实现回收转化中温位富余热量生产饱和蒸汽,保证制酸系统与铜冶炼系统的匹配化生产,节能减排效益可观.     

Better damage of chicory tissue by combined electroporation and ohmic heating for solute extraction

Damage of chicory tissue by combined electroporation and ohmic heating is studied for better solute extraction. Moderate (400–1000 V/cm) and high (10,000 V/cm) PEF treatments were applied varying pause duration between the trains of individual pulses. Ohmic heating was induced with increase of the number of trains N. Temperature dependence of tissue damage degree Z is evaluated for the different PEF intensities. With higher ohmic heating, chicory tissue is faster and better damaged. Electric field strengths of 600–800 V/cm combined with ohmic heating permit to enhance noticeably the solute extraction from chicory tissue. The solute diffusivity D for the different PEF treatments, is nearly the same for same values of Z. Chicory tissue treated to the same damage degree (Z = 0.8–1.0) using different PEF conditions (800, 1000 and 10,000 V/cm) has nearly the same diffusivity.Combined electroporation/ohmic heating pretreatment by moderate PEF (400–1000 V/cm) presents an interesting alterative for the treatment of high product throughputs (e.g. in the case of inulin production from chicory).     

铝电解预焙阳极脱落原因分析及对策

国内某电解铝企业电解槽频繁出现脱极现象,脱极率一度达到5%,造成原铝9970率大幅下降,阳极毛耗、氟盐单耗上升,电流效率下降,生产经营指标严重下滑。本文从残极炭碗状况、残极高度、磷铁环状况、磷铁成分、铁炭压降等几个方面进行观测,并对这些现象与脱极之间存在的因果关系进行分析,制定对策加以改进,最后得以扭转。     

An improved particle swarm optimisation for unit commitment in microgrids with battery energy storage systems considering battery degradation and uncertainties

Using electric storage systems (ESSs) is known as a viable strategy to mitigate the volatility and intermittency of renewable distributed generators (DGs) in microgrids (MGs). Among different electric storage technologies, battery energy storage (BES) is considered as the best option. In unit commitment (UC) module, the set of committed dispatchable DGs along with their power, power exported to/imported from macrogrid and status and power of ESS units are determined. In this paper, BES degradation is considered in UC formulation and an efficient particle swarm optimisation with quadratic transfer function is proposed for solving UC in BES‐integrated MGs, while the uncertainties of demand, renewable generation and market price are considered and dealt with robust optimisation. UC is formulated as a multi‐objective optimisation problem whose objectives are MG operation cost and BES degradation. The resultant multi‐objective optimisation problem is converted into a single‐objective optimisation problem and the effect of weight factors on MG operation cost and BES lifecycle are investigated. The results show that by consideration of BES degradation in objective function, BES lifecycle increases from 350 to 500 and the minimum depth of charge increases from 5.5% to 34%; however, MG operation cost increases from $8717 to $8910.2. The results also show that by consideration of uncertainties, MG's operation cost increases by 8.22%.     

A multiagent‐based microgrid operation method considering charging and discharging strategies of electric vehicles

In this paper, we propose a multiagent‐based microgrid (MG) operation method considering charging and discharging electric vehicles (EVs). The proposed system consists of five types of agents: single microgrid controller agent, several load agents, several gas turbines/engine agents, several photovoltaic generation agents, and several electric vehicle agents. In the proposed method, the load balancing can be realized by suppressing sudden fluctuations in supply and demand balance due to the synchronization of charging and discharging of EVs. From the simulation results, it can be seen that the proposed multiagent system could realize the load equalization in MG.     

刚果(金)某氧化铜精矿还原熔炼渣型优化实验

刚果（金）某地区经浮选得到的氧化铜精矿，含铜28.39 %，矿石中的铜主要赋存在孔雀石中。在实际生产中，采用鼓风炉还原熔炼处理该类氧化铜精矿，存在熔炼温度较高、氧化钙添加量大、熔炼渣含铜偏高的问题，为此，进行渣型优化实验研究，考察了还原焦比、CaO:SiO2比和氧化亚铁加入量对氧化铜精矿还原熔炼的影响。结果表明，在还原熔炼时，焦比主要影响粗铜产率和铜回收率，CaO:SiO2主要影响渣中铜含量，熔炼温度是影响渣黏度的主要因素。在还原焦比为5 %，选择酸性熔炼渣型，渣中CaO:SiO2为0.4-0.55，FeO:SiO2为0.13条件下，渣含铜可降至0.4 %以下，铜回收率在98 %以上。     

电场对竖直矩形微槽群润湿及表面温度的影响

微槽群在热流密度较大时会达到其毛细极限，可通过主动换热方式之一——电水动力学效应对其进行强化。本文为了研究电场对微槽群表面润湿特性和温度分布的影响，采用平板电极提供电场，蒸馏水作为工质，使用高速相机拍摄微槽内液体润湿长度，测量误差为2.97%～7.46%；使用红外热像仪拍摄电场作用下微槽群表面温度分布，测量误差为2.1%～2.39%。热流密度测量误差范围是9.66%～11.11%。结果表明：电场通过驱动微槽内流体向加热区域流动而提升其润湿性能，且较低热流密度下提升更好。因润湿性能的提升，微槽表面温度得以下降。随着电场增强，微槽横向温度分布的“波峰”、“波谷”差别加大，微槽纵向温度明显降低。当热流密度加大时，温降更为显著，1.4W/cm²热流密度、6kV电压下温降可达到30℃以上。温降的增加反映了电场对微槽的强化润湿进一步提升了微槽换热性能，且电场对较高热流情形下的微槽换热有着更为显著的强化效果。     

基于RBF网络滑模的电动助力制动系统液压力控制

针对汽车电动助力制动系统（Electro-booster，EBooster）的液压力控制中液压负载的非线性和不一致性问题，提出一种基于径向基函数（Radial based function，RBF）神经网络的滑模变结构控制方法。设计EBooster系统压力控制架构，建立液压制动系统等效结构简化模型，据此设计基于RBF网络滑模变结构的液压力控制方法，通过设计RBF网络的自适应律来实现系统滑模控制参数的自适应调整，并利用李雅普诺夫函数方法分析算法的稳定性。最后搭建电动助力制动系统的快速原型试验平台来验证算法的有效性。试验结果表明，采用RBF神经网络滑模变结构的控制策略对电动助力制动系统液压力的控制误差在2%以内，具有良好的控制效果。研究成果为EBooster系统的压力控制提出一种具有良好自适应性的算法设计思路。     

Effects of the film thickness and poling electric field on photovoltaic performances of (Pb,La)(Zr,Ti)O3 ferroelectric thin film-based devices

The ferroelectric photovoltaic (FPV) effect obtained in inorganic perovskite ferroelectric materials has received much attention because of its large potential in preparing FPV devices with superior stability, high open-circuit voltage (V_oc) and large short-circuit current density (J_sc). In order to obtain suitable thickness for the ferroelectric thin film as light absorption layer, in which, the sunlight can be fully absorbed and the photo-generated electrons and holes are recombined as few as possible, we prepare Pb_0.93La_0.07(Zr_0.6Ti_0.4)_0.9825O₃ (PLZT) ferroelectric thin films with different layer numbers by the sol-gel method and based on these thin films, obtain FPV devices with FTO/PLZT/Au structure. By measuring photovoltaic properties, it is found that the device with 4 layer-PLZT thin film (~300 nm thickness) exhibits the largest V_oc and J_sc and the photovoltaic effect obviously depends on the value and direction of the poling electric field. When the device is applied a negative poling electric field, both the V_oc and J_sc are significantly higher than those of the device applied the positive poling electric field, due to the depolarization field resulting from the remnant polarization in the same direction with the built-in electric field induced by the Schottky barrier, and the higher the negative poling electric field, the larger the V_oc and J_sc. At a -333 kV/cm poling electric field, the FPV device exhibits the most superior photovoltaic properties with a V_oc of as high as 0.73 V and J_sc of as large as 2.11 μA/cm². This work opens a new way for developing ferroelectric photovoltaic devices with good properties.     

基于Stateflow电力机车变流器控制设计与实现

某出口型号交流电力机车牵引控制系统要求变流器控制逻辑具备接触器控制、牵引系统数据交互、变流器故障保护、变流器启动自检等功能。针对以上功能,基于MATLAB中的Simulink/Stateflow可视化编程工具进行牵引控制模型的搭建,遵循模块化编程理念,采用较少的程序代码编写实现复杂的逻辑控制模型,生成逻辑清晰的控制功能流程图,进行半实物仿真测试,增强控制模型的可靠性。通过该变流器产品型式试验检验,验证变流器控制逻辑的功能可以满足控制系统的需求。